What did you do in your reloading room today?

[badbrass]

I hope so! It will shoot as good as yours!

Originally Posted by huntinstuff

Nice! The one I had shot extremely well. Im sure yours will too

[birdseye]

I purchased a new gun safe that was on sale,organized while loading it and realised I could use another one lol Almost everything fit

[6.5 shooter]

Originally Posted by Dean2

If you use a heat gun to soften the bedding it comes out REALLY easy. Most bedding softens at around 220 to 250 F, so far below anything that would harm wood or most stocks. A lot less work than gouging it out.

Thanks Dean 2 will give it a try.

[Engels]

primed 40 cases on friday evening. Loaded up a powder ladder sunday morning. Now to find some time to get out to the range!

[partsman]

Going to start loading for two savage 24 V from an auction in 222/20 gauge , and have a 270 wsm coming, so have to load up brass I have had for awhile and see how it does.

[6.5 shooter]

De primed and removed crimped on 91ct, .223 Mil brass, uniformed primer pockets, ran neck arbors through the necks, trimmed all to length, wet tumbled and dried for storage. Have another 150ct. coming soon, so no rest for the wicked. Lot's of work, hope it is worth it. Now, I just need dies and a rifle. LOL

[catnthehat]

Loading some 6.5X43 MS this morning for the Mannlicher carbine.
Cat

[6MT]

I got back into the reloading business. Just kidding. But today after my road race, I started to replenish my stores. I loaded a modest hundred rounds of .45 Colt.

[obsessed1]

Made a new ejector for my 9.3x62 mauser. Original one was only ejecting about 60% of the time....not near good enough for me so I fabbed up a new one. Ill probably need to make a new one in the future as the only steel I had handy was .049 thick. Original was .059 thick...It will run for now.

[6.5 shooter]

Deprimed 259 , .223 PMC factory brass. the stock pile grows.

[6.5 shooter]

Prepped other 350, rds of .223 today, right shoulder is a bit sore...LOL. Finally found my RCBS dies. Life just got a whole bunch easier.

[Engels]

deprimed and tumbled 60 cases of once fired 300 wsm for my dad. Looking forward to helping him develop a load for his gun.

[6.5 shooter]

As you all know I have been doing a bunch of brass prep in .223. Well I trimmed 91 cases today with the FC head stamp.

*10 were in trim length specs. (1.760"-1.750")
*15 or more (I never counted) were more then spec. length by at least ~20 thou.
*The rest were ~20 thou under minimum trim length. Now this does not make these unsafe. BUT the over length brass is quite worry some.
This is once fired brass.

Play safe everyone!

[honda610]

I built 2 shelves above my garage door. Then I started organizing. Found a pile of loaded 20 gauge,12 gauge 9mm, 7.62x39, 556

[birdseye]

neck sized and reload half dozen 338 Rum rounds

[Ackleyman]

prepped brass and loaded bunch a .222 rounds , thks to Bud for giving me Lb of IMR 4198.

[catnthehat]

Loading 30/30AI rounds to shoot tomorrow out of the #3 donor rifle.
Normally I wouldn't shoot a donor gun, but the barrel amd stock set will be sold and I want to make sure the barrle is accurate so I can out an appropriate
Price on it
Cat

[catnthehat]

Welp, got the scope on the #3 in 3030AI, loaded 20 rounds, and scoped the bore- CHANGE OF PLAN!
The barrel is so nice I'm just going to sell it with the bore scope pics.
Now I have some bullets to pull, and a scope to take out of the rings! LOL
Cat

[6.5 shooter]

Just spent money in an auction that I don't have Does that count as future work in the reloading room?

[GoneOutdoors]

Built the first load up for my 280ai. 160gr nosler accubonds. Started a grain lower than what the book max was and ended up 2 grs over the max load with still zero signs of pressures or stress and no sticky bolt. Finally got to what the book fps said. Using h4831sc and fed210 primers. 2945/2949fps. More or less what i was hoping for and a pretty darn good group at .75moa and felt good.

Built up a ladder test for my uncles 300wm. 180gr speer boattails... Ran imr4831 as its test. Went with Sami specs and book load - chrono said 3060/3067... 5 shots touching at sami length.

What a day. Loaded all the bullets remaining, filled out the log book with a crisp one to enjoy the rest of the evening.


Sent from my iPhone using Tapatalk

[H380]

Cleaned mine up so I could make it to the gun safe ..

Sent from my SM-G781W using Tapatalk

[catnthehat]

410 day, loading some #12 1/2 oz loads .
Cat