|
02-10-2018, 10:29 AM
|
|
|
Join Date: Apr 2010
Posts: 553
|
|
Tips from removing stuck ice auger bit from shaft?
I have tried heat and wd40 wondering if anyone has any other ideas. Thanks for the help.
Rob
|
02-10-2018, 11:05 AM
|
|
|
|
Join Date: Jan 2012
Location: 204
Posts: 5,440
|
|
Take out the bolt.
__________________
"I like to quote my own quotes" ~ Dewey Cox
|
02-10-2018, 11:07 AM
|
|
|
|
Join Date: Feb 2015
Location: Near Lac La Biche, Ab.
Posts: 575
|
|
Have you tried soaking the connection with penetrating oil?
If not, try soaking, stand auger upright and apply penetrating oil to the auger flyte, and auger transmission output shaft. Kriol is a good penetrant, might be hard to find though, I think sea-foam makes one called deep creep, it works good.
Try to rotate the auger, until you can get it to move slightly, once it starts to move, just keep working it. If you have a vice grip with the chain, for pipe, this will work good to keep the auger powerhead from rotating with the auger flyte.
Be careful with how much heat you apply, once the auger transmission output shaft is the same temp as the outside of the flyte temp, it will be basically size on size, and will be seized.
Ideally you want to make the auger flyte connection, a higher temp than the auger transmission output shaft.
I'm assuming that the bolt has been removed from the auger flyte connection, and did not leave any burrs inside the auger flyte connection area?
Alternatively you can use a couple of flat pry bars on the top edge on the flange of the auger flyte and the bottom of the auger transmission, use some spacer blocks, if the space is to large.
What kind of auger is it?
|
02-10-2018, 11:08 AM
|
|
|
|
Join Date: Feb 2009
Posts: 12,770
|
|
lube and kick it. then clean both ends up with emery cloth once you get it apart.
__________________
Dinos
681
Shove your masks and your vaccines
Non Compliance!!!!!!
"According to Trudeau, Im an extremist who needs to be dealt with"
#Trudeau must go
Wheres The Funds
The vaccine was not brought in for COVID. COVID was brought in for the vaccine. Once you realize that, everything else makes sense.” ~ Dr. Reiner Fuellmich
|
02-10-2018, 11:11 AM
|
|
|
Join Date: Apr 2010
Posts: 553
|
|
Yes the retaining bolt is out. just that bit has not been off in over 10 years so just looking for ideas.
|
02-10-2018, 11:45 AM
|
|
|
|
Join Date: Jun 2007
Location: Calgary
Posts: 570
|
|
Try heating the crap out of it then throw some ice cold water or snow on it a few times that always seems to work when I have stuck things at work.Spray wd 40 on when it’s hot.
|
02-10-2018, 11:56 AM
|
|
|
Join Date: Mar 2009
Location: Edmonton
Posts: 9,672
|
|
Heat should have broken any rusty crud in the threads. I would try again but heat it up more.
|
02-10-2018, 12:02 PM
|
|
|
Join Date: Sep 2007
Location: St. Albert
Posts: 340
|
|
Auger
If you can get to the lake, run the auger and start a hole with the bolt removed.
This has worked for me in the past when I had a similar issue.
Good Luck,
Phil
|
02-10-2018, 02:56 PM
|
|
|
|
Join Date: Feb 2010
Location: Fort Saskatchewan
Posts: 733
|
|
"Kriol is a good penetrant,"* As Kuduhntr suggested is awesome to loosen rusted metal. If you can't find it make some with diesel fuel and ATF. Let it soak and drill a hole with out the bolt in, stop before going all the way through and keep going till it breaks loose.
|
02-10-2018, 03:49 PM
|
|
|
|
Join Date: Sep 2013
Location: Calgary
Posts: 1,721
|
|
Quote:
Originally Posted by Dewey Cox
Take out the bolt.
|
|
02-10-2018, 03:53 PM
|
|
|
|
Join Date: Jan 2012
Location: 204
Posts: 5,440
|
|
Quote:
Originally Posted by Phil
If you can get to the lake, run the auger and start a hole with the bolt removed.
This has worked for me in the past when I had a similar issue.
Good Luck,
Phil
|
If you drill a hole over at least 40’ of water, Murphy’s law will ensure it comes loose as soon as you’re through the ice.
__________________
"I like to quote my own quotes" ~ Dewey Cox
|
02-11-2018, 07:59 AM
|
|
|
|
Join Date: Jan 2010
Location: Edmonton
Posts: 6,470
|
|
If your trans gears are plastic, the heat might ruin them ! Penetrating oil, good vise or chain vise grips. You need to some how wedge the auger shaft from turning also.
Its a good idea to service these things once in a while, like removing the bit and putting some anti seize compound on the shaft. Checking every couple of times that the bolt is tight etc....
__________________
Kim
Gonna get me a 16" perch.
|
02-11-2018, 08:12 AM
|
Banned
|
|
Join Date: Feb 2015
Location: south calgary
Posts: 2,281
|
|
It may be that your auger was loose at one time and there is now a bur on the shaft at both pieces. Explore drilling out a smidge. Ive never seen one that fit tight like that before
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 03:06 PM.
|