.243 Barnes load data for 80gn ttsx

[heretohunt]

Could someone please look up some load data for me in an old Barnes manual. I’m looking for the 80 grain TTSX data for 243.
H4340 and Varget loads specifically but other options are alway good. I am hearing some conflicting information and thought it would be best to go to the source.
It seems like the current online data is pretty limited.
Thank you.

[spurly]

https://www.barnesbullets.com/wp-con...Winchester.pdf

[heretohunt]

Originally Posted by spurly

https://www.barnesbullets.com/wp-con...Winchester.pdf

Thank you for that. I have seen that and the loads I’m looking for are not there. Actually, I only have the one of those powders and it’s not great in my rifle.

[madcarpenter]

It’s a wicked little bullet. Push it fast and accurate. It’s my current go to 243 bullet.


-Mad

[FishOutOfWater]

It's not from the Barnes manual, and is for the 85gr TSX, but maybe helpful...

[PartTimeHunter]

Did you try looking here:

https://hodgdonreloading.com/?_ga=2....939.1645033436

[Hunter Trav]

Here is the data from the Barnes #4 manual. Hopefully the pic is clear enough for you.

Sent from my SM-A037W using Tapatalk

[Hunter Trav]

Pic didnt add for some reason on that first reply...

Sent from my SM-A037W using Tapatalk

[heretohunt]

Thank you. Is there anything for the 80 gr TTSX?

[heretohunt]

Here is some feedback if anyone is interested.
Of course, I will give you the disclaimer that this is in my rifle and I will not be using it in my other one without working up. If you choose to use this data, you should do the same.
243 Winchester, with 80 gr TTSX, Coal. 2.61 inches, federal 210 primers, Winchester, brass, and h4350
I started at 40.5 gn and got 3023 ft./s. I carefully worked my way up to 45.7 grains with no pressure signs. The speed there was 3446.4 ft./s. Probably I will be using 45 grains as it looks like a promising node.

[FishOutOfWater]

Originally Posted by heretohunt

Here is some feedback if anyone is interested.
Of course, I will give you the disclaimer that this is in my rifle and I will not be using it in my other one without working up. If you choose to use this data, you should do the same.
243 Winchester, with 80 gr TTSX, Coal. 2.61 inches, federal 210 primers, Winchester, brass, and h4350
I started at 40.5 gn and got 3023 ft./s. I carefully worked my way up to 45.7 grains with no pressure signs. The speed there was 3446.4 ft./s. Probably I will be using 45 grains as it looks like a promising node.

If you're not seeing pressure signs, I guess. But I would've started a few grains lower, and probably would not exceed ~42gr... If it were me.

I say this because of the data for the 85gr I posted, and the data on Hogdon for the Hornady 80gr GMX (which has almost identical S/D and coefficient as the TTSX).

And ~3450 FPS is really pushing it with an 80gr...

[madcarpenter]

[Bushrat]

Originally Posted by heretohunt

Here is some feedback if anyone is interested.
Of course, I will give you the disclaimer that this is in my rifle and I will not be using it in my other one without working up. If you choose to use this data, you should do the same.
243 Winchester, with 80 gr TTSX, Coal. 2.61 inches, federal 210 primers, Winchester, brass, and h4350
I started at 40.5 gn and got 3023 ft./s. I carefully worked my way up to 45.7 grains with no pressure signs. The speed there was 3446.4 ft./s. Probably I will be using 45 grains as it looks like a promising node.

Brass dosen't generally show signs of over pressure till about 70,000+ /psi which is way over pressure. Velocity above what book maximums show is a sign of overpressure. Most of us without pressure testing equipment cannot tell what pressure value we are dealing with as we have no way to test for it. The best measure of pressure most shooters have available to them is velocity, if we are getting higher velocity than the books show with their max loads or higher than max load we should pay attention to it. It is good that rifles have a safety threshold built into them and won't blow up with overcharges but because they may not blow up dosen't mean the rifle will not eventually show cumulative damage like lug setback and metal fatigue if overcharges are continually used over time.

[catnthehat]

I ignore most pressure signs except for velocity and bolt lift- if you have hard bolt lift, you are already over pressure for your riflle no matter what the books say as far as data goes .
Cat

[Hunter Trav]

Originally Posted by heretohunt

Thank you. Is there anything for the 80 gr TTSX?

No sorry nothing for the 80gr. Next closet one down was a 75gr TSX I believe.

[madcarpenter]

The 80gr load data is on their web page. It’s been updated.

[stob]

I used the load data on the superformance cannister..approx 3500fps and accurate