|
|
02-17-2022, 07:24 PM
|
|
|
|
Join Date: Jun 2007
Location: Ft. McMurray
Posts: 38,991
|
|
No loading today, great day to be at ther range though- until I got there!
Oh well, session was good, just couldn't see through the spotter for snow to figure out what I was doing on the steel with the irons at 500, so just kept banging it , then went down to check afterwards.
Cat
__________________
Anytime I figure I've got this long range thing figured out, I just strap into the sling and irons and remind myself that I don't!
|
02-17-2022, 07:28 PM
|
|
|
|
Join Date: Sep 2011
Location: Sherwood Park, Alberta
Posts: 493
|
|
Did some case prep for my hunting rifle! 7RM.
__________________
My mom says I'm a keeper.
|
02-17-2022, 08:42 PM
|
|
|
|
Join Date: Sep 2008
Location: Edmonton Alberta
Posts: 9,935
|
|
20 rds of 30-30
150g hornady interlocks
31g of IMR 3031
Kinda exactly what my newer 30-30 likes.....
__________________
When you are born, you get a ticket to the Freak Show.
If you are born in Canada, you get a front row seat.
|
02-17-2022, 10:47 PM
|
|
|
|
Join Date: May 2009
Location: Morinville
Posts: 1,316
|
|
I ordered some more gas-checks for my 30-30 and 308 casts then I found my box of 1000 Hornady’s.
|
02-19-2022, 10:58 PM
|
|
|
|
Join Date: Apr 2014
Location: Parkland County
Posts: 1,176
|
|
After de-capping, wet tumbling, F.L. sizing, neck flaring, and priming……..ready for powder. Whew!
200 cases of .44mag
|
02-21-2022, 02:29 PM
|
|
|
Join Date: Feb 2021
Posts: 434
|
|
Prepped some 6.5 PRC brass, and loaded some 303 British for a ladder test.
Thinking for a reason not to pretty my 7mm-08 brass. Bit lazy today.
|
02-21-2022, 04:30 PM
|
|
|
|
Join Date: Sep 2008
Location: Edmonton Alberta
Posts: 9,935
|
|
44 rounds of 300 wsm.
200g nosler partitions with 61g of imr4350
I need some 30 cal 165g accubonds
__________________
When you are born, you get a ticket to the Freak Show.
If you are born in Canada, you get a front row seat.
|
02-22-2022, 10:06 AM
|
|
|
Join Date: Feb 2021
Posts: 434
|
|
I ended up getting off my azz, and doing the prep on 143 cases on the 7mm-08.
Primers in 50, and a new load development ready for the range.
-18* is just not the range day I wanted to have, so I await for the warmer stuff.
|
02-22-2022, 11:52 AM
|
|
|
Join Date: Dec 2011
Location: East Kootenays, BC
Posts: 1,204
|
|
I have been chronograph testing loads for my old 7 STW, which has been languishing in the safe for about 15 years. Today I trimmed all my fired brass, cleaned primer pockets, and primed 50 cases. I had some very encouraging results last week with 140's and IMR 7828, will do some accuracy testing when it warms a bit. These things are fast!
|
02-27-2022, 04:46 PM
|
|
|
Join Date: Oct 2010
Location: Near Drumheller
Posts: 7,021
|
|
I have the V4 Autotrickler here now, need to assemble that and try it out, also need to put a B&C stock on a Tikka T3X. At the moment though, I have no ammo that needs to be loaded, have 5 or 6 guns that need to have some rounds put thru them though, and some weather that is suitable for it. Only outstanding order I have coming still, are some RWS Evo bullets for the 30R, due in April or so.
__________________
You should also be a member;
CCFR
CSSA
|
02-27-2022, 05:11 PM
|
|
|
|
Join Date: Apr 2014
Location: Parkland County
Posts: 1,176
|
|
Quote:
Originally Posted by 32-40win
I have the V4 Autotrickler here now, need to assemble that and try it out, also need to put a B&C stock on a Tikka T3X. At the moment though, I have no ammo that needs to be loaded, have 5 or 6 guns that need to have some rounds put thru them though, and some weather that is suitable for it. Only outstanding order I have coming still, are some RWS Evo bullets for the 30R, due in April or so.
|
You should get used to the V4 by throwing some charges. You need to figure out flow rates and a good transition point between tubes. Don’t set that transition point below about 1.7gr. (My experience.)
If this is your first AutoTrckler, you will be impressed. I still use my V3 for fine ball powders. (Although I have tried those in the V4.) Extruded powders work really well in the V4.
Have fun with it. Congrats!
|
02-27-2022, 05:16 PM
|
|
|
|
Join Date: Sep 2008
Location: Edmonton Alberta
Posts: 9,935
|
|
Made 50 30-30 rounds with new Starline brass and PRVI Partizan 150g round nose bullets....
Worth a try.....
__________________
When you are born, you get a ticket to the Freak Show.
If you are born in Canada, you get a front row seat.
|
02-27-2022, 05:56 PM
|
|
|
Join Date: Jan 2013
Location: onoway, Ab
Posts: 7,282
|
|
Quote:
Originally Posted by 32-40win
I have the V4 Autotrickler here now, need to assemble that and try it out, also need to put a B&C stock on a Tikka T3X. At the moment though, I have no ammo that needs to be loaded, have 5 or 6 guns that need to have some rounds put thru them though, and some weather that is suitable for it. Only outstanding order I have coming still, are some RWS Evo bullets for the 30R, due in April or so.
|
What was your wait time to get a V4?
|
02-27-2022, 10:33 PM
|
|
|
|
Join Date: Apr 2014
Location: Parkland County
Posts: 1,176
|
|
Loaded a hundred each of .45LC, .357mag, and .38 spl.
|
02-28-2022, 10:43 AM
|
|
|
Join Date: Jan 2021
Location: Edmonton
Posts: 211
|
|
Prepped 50 new brass for the .257 Roberts. Loaded 2 test ladders, one with Hornady 117 Interlocks over Reloder 16 and Nosler 120 Partitions over IMR 4350.
Prepped 50 rounds of brass for the 270's. Starting loading 2 test ladders for them and will finish today.
Also had packages delivered from Hirsch Precision and Prophet River. Redding dies for the 7x57 and a set for the 284 Winchester build I'm going to do.
100 Lapua brass for the 284 and 50 R-P brass for the 257. Forster micrometer seating dies for the 22-250 and 223.
|
03-01-2022, 11:39 AM
|
|
|
Join Date: Jan 2009
Location: Brooks
Posts: 2,254
|
|
reloading room
Loaded up 20 test loads for my new (to me) .308. Havent shot a .308 win for quite a number of years, since getting "magnumitis" many years back. Still prefer bigger cartridges, with heavy for caliber bullets, but should make a nice soft-shooting deer rifle.
Loaded up a bunch of Kynoch brass now that Catnthehat was kind enough to supply me with some berdan primers! My old side by side hammer gun in
450 3 1/4" will have lots more fodder to get ready for spring bear! I also have an old Field's Patent falling block in the same caliber that I am trying to get sighted in. Just need the weather to cooperate and I am ready for the range.
__________________
"a gun without hammers is like a spaniel without ears!"
|
03-01-2022, 12:10 PM
|
|
|
|
Join Date: Jun 2007
Location: Ft. McMurray
Posts: 38,991
|
|
Busy chambering an empty round into some of my rifles and sliding the bore scope in from the muzzle to check stuff like Distince from the case mouth to the actual leade , some very interesting discoveries for sure!
Cat
__________________
Anytime I figure I've got this long range thing figured out, I just strap into the sling and irons and remind myself that I don't!
|
03-01-2022, 12:12 PM
|
|
|
|
Join Date: Jun 2007
Location: Ft. McMurray
Posts: 38,991
|
|
Quote:
Originally Posted by oldgutpile
Loaded up 20 test loads for my new (to me) .308. Havent shot a .308 win for quite a number of years, since getting "magnumitis" many years back. Still prefer bigger cartridges, with heavy for caliber bullets, but should make a nice soft-shooting deer rifle.
:
|
308??!! WTH, you goin' all smallbore on us or what ??
Cat
__________________
Anytime I figure I've got this long range thing figured out, I just strap into the sling and irons and remind myself that I don't!
|
03-01-2022, 12:24 PM
|
|
|
|
Join Date: May 2009
Location: Morinville
Posts: 1,316
|
|
Planned on sizing some .30 cal 200gr Lee RNGC cast boolits today but real work got in the way.
Eventually I would like to load up some more Slugs R Us cast Hammerhead 12g slugs.
|
03-01-2022, 02:57 PM
|
|
|
|
Join Date: Apr 2014
Location: Parkland County
Posts: 1,176
|
|
Loaded another hundred rounds of .44mag last night.
|
03-01-2022, 11:12 PM
|
|
|
Join Date: Jan 2009
Location: Brooks
Posts: 2,254
|
|
.308
Quote:
Originally Posted by catnthehat
308??!! WTH, you goin' all smallbore on us or what ??
Cat
|
If I dont like it for deer, it will make a decent gopher gun Should leave less of a divet than the rigby at least.
I even bought a 7-08 this winter. Havent shot anything with it yet, but I fell in love with the wood. Nothing sells a gun to me harder than a good piece of marbled walnut!
__________________
"a gun without hammers is like a spaniel without ears!"
|
03-01-2022, 11:33 PM
|
|
|
|
Join Date: Jun 2007
Location: Ft. McMurray
Posts: 38,991
|
|
Quote:
Originally Posted by oldgutpile
I even bought a 7-08 this winter. Havent shot anything with it yet, but I fell in love with the wood. Nothing sells a gun to me harder than a good piece of marbled walnut!
|
HAHA! yeah, I know all about that!
Cat
__________________
Anytime I figure I've got this long range thing figured out, I just strap into the sling and irons and remind myself that I don't!
|
03-02-2022, 08:59 AM
|
|
|
|
Join Date: Jun 2007
Location: Ft. McMurray
Posts: 38,991
|
|
Getting ready to do some load testing with some N550 and N555 as I am now out of RL26 for my 244RemAI.
Cat
__________________
Anytime I figure I've got this long range thing figured out, I just strap into the sling and irons and remind myself that I don't!
|
03-12-2022, 12:59 PM
|
|
|
Join Date: Jan 2021
Location: Edmonton
Posts: 211
|
|
Been a reasonably busy week at the bench building test loads for various calibers and stocking up on .204 gopher pills.
Just finished 200 rounds of Nosler 40 gr. Ballistic Tip Varminters over 25.5 grs of Benchmark for the .204.
Today I'm working on 100 rounds of Sierra 39 gr. Blitz Kings over the same powder and charge.
Two test loads for my sons 7mm-08.
- Barnes 120 TTSX over H4895
- Barnes 140 TSX over Reloder 15
Two test loads for .243 Win. in a Winchester Featherweight
- Barnes 80 gr. TTSX over H414
- Nosler 90 gr. Accubond over Reloder 16
Two test loads for my .257 Roberts in a Winchester Featherweight.
- Hornady 117 gr. BTSP over Reloder 16
- Nosler 120 Partition over IMR 4350
Two test loads for one of my .270's in a Winchester Featherweight
- Speer 130 gr. HotCor over Reloder 16
- Hornady 130 gr. Interlock over H4831sc
|
03-12-2022, 05:00 PM
|
|
|
|
Join Date: Jun 2007
Location: Ft. McMurray
Posts: 38,991
|
|
Been a pretty busy last few weeks at the range, so I have to load some more Vitivouri for the 244RemAI and Varget loads for the
Mouse gun!
The Vitivouri N555 worked out great fir the 244AI, am able to hold inside 3MOA at 700M with the sling'n'irons
Cat
__________________
Anytime I figure I've got this long range thing figured out, I just strap into the sling and irons and remind myself that I don't!
|
03-13-2022, 03:43 PM
|
Banned
|
|
Join Date: Mar 2009
Posts: 5,700
|
|
Loaded up 80 rounds of 6 gt
Looking to see if they prefer a little extra jump
Searching in the 45 thou range and further
|
03-13-2022, 11:07 PM
|
Banned
|
|
Join Date: Mar 2009
Posts: 5,700
|
|
Quote:
Originally Posted by marky_mark
Loaded up 80 rounds of 6 gt
Looking to see if they prefer a little extra jump
Searching in the 45 thou range and further
|
Successsssss!!!!!!
This cartridge is starting to make me smile
It’s no Grendel but hey, what can compete with that
🤷*♂️😂😂😂😂
|
03-16-2022, 07:01 AM
|
|
|
Join Date: Jun 2007
Posts: 1,030
|
|
Primed 200 17 Fireball
Primed 150 221 Fireball
Primed 200 17 Hornet
The great gopher season will soon be upon us.
__________________
Visit the Peace Country Fish & Game Association
PCFGA on Facebook
|
03-16-2022, 08:55 AM
|
|
|
Join Date: Dec 2008
Location: Camrose
Posts: 46,524
|
|
I ran a new loader through the basics, from setting up his dies, to determining the jump to the lands. Of the two new people I am mentoring, I have high hopes for one, the other one is not catching on as quick.
__________________
Only accurate guns are interesting.
|
03-20-2022, 07:45 AM
|
|
|
|
Join Date: Apr 2014
Location: Parkland County
Posts: 1,176
|
|
Magnum brass prep day. The .338LM case gets F.L. sized and trimmed today.
Shoulder gets bumped .0005” from fire formed. Neck tension with the bushing is .002”. And trim length……yeah, I had forgotten how much I hate trimming. It’s in spec, that’s all I’ll say.
This gets the cases ready for powder (after priming, of course).
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 06:44 AM.
|