|
07-21-2020, 12:29 PM
|
|
|
Join Date: Aug 2008
Location: calagry
Posts: 1,928
|
|
Lund boat floor repair
Long story short boat got punctured by trailer thru the floor. Any suggestions in where to take for repairs ? Thanks.
https://photos.app.goo.gl/skh8mX8JAZUX1xPF8
|
07-21-2020, 12:35 PM
|
|
|
|
Join Date: Dec 2012
Location: At the end of the Thirsty Beaver Trail, Pinsky lake, Alberta.
Posts: 24,726
|
|
JB Weld..do the repair yourself....fixed a few aluminum boats up to and including green duck tape in a pinch....good luck.
__________________
Be careful when you follow the masses, sometimes the "M" is silent...
|
07-21-2020, 01:49 PM
|
|
|
Join Date: Jul 2011
Posts: 2,050
|
|
Dang those riveted hulls are thin.
1) Put a 2x4 on the other side, 2x4 on this side and gently tap it down with a hammer.
2)Find a competent welder to tig it.
|
07-21-2020, 02:28 PM
|
Banned
|
|
Join Date: Jan 2009
Location: Perdue SK
Posts: 1,570
|
|
Quote:
Originally Posted by Jayhad
Dang those riveted hulls are thin.
1) Put a 2x4 on the other side, 2x4 on this side and gently tap it down with a hammer.
2)Find a competent welder to tig it.
|
This, except let the welder move the medal.
|
07-21-2020, 07:58 PM
|
|
|
Join Date: Jul 2015
Posts: 292
|
|
Quote:
Originally Posted by kinwahkly
|
Iron aero marine
|
07-21-2020, 08:18 PM
|
|
|
|
Join Date: Jul 2010
Location: Edmonton
Posts: 11,868
|
|
Yeah I'd weld it if you know someone but he's gotta pretty good on that thinner sheet as it's going to take someone with some experience.
You could also flatten it, JB weld it, and even add a little plate - with proper rivets and seal those up.
Depending on your budget and if you care if there's a little leak or not. Only a weld can guarantee it's 100% waterproof. JB might do it, probably will, but who knows over the long run. I have successfully used it on some really bad cracks and separations and it was 100% dry on a boat and had complete failures on really small and easy holes using JB.
|
07-21-2020, 09:52 PM
|
|
Moderator
|
|
Join Date: Jun 2010
Location: Stony Plain
Posts: 6,685
|
|
When I used to work for Arctec alloys we had a product for soldering aluminum. I used to demo it by punching a half inch hole in the bottom of a pop an and soldering it shut with a propane torch and the soldering material. Worked very well as long as you followed procedure.
Arctec Alloys is located in the north end of Calgary just off Hwy 2 . Give them a call and ask for. A tech rep. They will help you out.
|
07-22-2020, 08:16 AM
|
|
|
Join Date: Jul 2015
Location: Devon/Spruce Grove
Posts: 343
|
|
Like already said, maybe get a small piece and rivet it in after flattening it out, then maybe put some Eternabond tape over it on the outside? I've added a small roll of Eternabond tape to my little tool box that I keep on my boat because it could seriously get me out of trouble it I was out on the river and got a hole from a rock or something like that. I've been using this stuff on everything lately, I love the stuff. Once it touches, you're not moving it again. It's meant for RV roof repair and it's worth the money.
Kind of a Red Green fix though.
|
07-23-2020, 06:28 PM
|
|
|
Join Date: Aug 2008
Location: calagry
Posts: 1,928
|
|
Took it to Iron Areo . Highly recommended.
|
07-23-2020, 06:32 PM
|
|
|
|
Join Date: Nov 2008
Posts: 11,424
|
|
Quote:
Originally Posted by kinwahkly
Took it to Iron Areo . Highly recommended.
|
Did they weld it or rivet it?
__________________
“One of the sad signs of our times is that we have demonized those who produce, subsidized those who refuse to produce, and canonized those who complain.”
Thomas Sowell
|
07-23-2020, 07:26 PM
|
|
|
Join Date: Aug 2008
Location: calagry
Posts: 1,928
|
|
They are going to weld it.
|
07-23-2020, 08:04 PM
|
|
|
Join Date: Nov 2019
Posts: 604
|
|
Good move. The annealing can be the tricky part on that.
Osky
|
07-23-2020, 08:45 PM
|
|
|
Join Date: Jun 2009
Location: Dodge City
Posts: 1,283
|
|
I think welding is the way to go, even though it's going to be light aluminum if you get someone who knows what they are doing it will last. I used to have an old Harbercraft tinner that was ridiculously light aluminum.
Long story short a hole very similar to yours got punched in it and after a good weld job ran that boat for another 10 years with no issues before it got sold.
|
07-26-2020, 04:15 PM
|
|
|
Join Date: Aug 2008
Location: calagry
Posts: 1,928
|
|
So it's at Iron Areo now. What a mess going up that Spray lakes road the last year and a half. Just a reminder for newbies like me always check and recheck straps etc on the boat. So the front strap came loose or wasn't tightened enough band the back straps also were to loose so the boat basically bounced up and down on the trailer . One of the numbers also came loose and one of the metal brackets came thru the boat. Lessoned learned.
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 10:24 AM.
|